Made some chips w the SouthBend
2 posters
48-84 :: Your first category :: 66-84
Page 1 of 1
Made some chips w the SouthBend
Lathe is wired right, thanks Russ...
Tonite I started machining down an axle for the flattie project, got a new hub I'm lacing in and it's needing a slightly smaller dia axle.
Damn that old lathe runs nice, been readin up in that book Koot lent me, gettin the hang of it bit by bit LOL. Need a dead center, got one comin in the mail. I'll post some pics.
Tonite I started machining down an axle for the flattie project, got a new hub I'm lacing in and it's needing a slightly smaller dia axle.
Damn that old lathe runs nice, been readin up in that book Koot lent me, gettin the hang of it bit by bit LOL. Need a dead center, got one comin in the mail. I'll post some pics.
sunnydog- Posts : 2053
Join date : 2012-10-28
Age : 55
Location : Akimbo Alogo
Re: Made some chips w the SouthBend
...and thanks Larry for the cutting tools.
There's so much to learn here.
There's so much to learn here.
sunnydog- Posts : 2053
Join date : 2012-10-28
Age : 55
Location : Akimbo Alogo
Re: Made some chips w the SouthBend
Here's the Hallcraft mini-drum I'm lacing in...when I say lacing, it's lacing me with painful bitchslaps
Well, I gotta wait on the other half of the spokes, but this is how it will look roughly
So here's my slow turnin' process
Peace out
Well, I gotta wait on the other half of the spokes, but this is how it will look roughly
So here's my slow turnin' process
Peace out
sunnydog- Posts : 2053
Join date : 2012-10-28
Age : 55
Location : Akimbo Alogo
Re: Made some chips w the SouthBend
Got that axle whittled down to fit the Hallcraft, needed a spacer so fitted my new old chuck in there and made some real spindrift...trying to earn my "swarfrat" rating!
sunnydog- Posts : 2053
Join date : 2012-10-28
Age : 55
Location : Akimbo Alogo
Re: Made some chips w the SouthBend
Hope this pic shows the setup better
Reduced the axle from 3/4 down to 5/8 to fit the hub
Once I got that spacer hogged out I'll assemble it all and test fit
Reduced the axle from 3/4 down to 5/8 to fit the hub
Once I got that spacer hogged out I'll assemble it all and test fit
sunnydog- Posts : 2053
Join date : 2012-10-28
Age : 55
Location : Akimbo Alogo
Re: Made some chips w the SouthBend
Little hard to tell and you didn't mention it;but,did you step the axle on one side?You refer to THEE spacer (as in 1?).
Dennman- Posts : 1446
Join date : 2012-10-31
Age : 75
Location : Courtenay
Re: Made some chips w the SouthBend
Yes Dennman, I stepped it down.... Left the one side at 3/4 dia, it sits against the hub bearing on drivers side, other side I milled a spacer to provide support...sorry the pics need resizing, lose a good portion of the detail transferring.
sunnydog- Posts : 2053
Join date : 2012-10-28
Age : 55
Location : Akimbo Alogo
Re: Made some chips w the SouthBend
You're a quick study Sunny! That's a nice lookin finish on that axle.
I just now flashed back on last nights dream.A beauty little milling machine w/ all kinds of tooling and gauges that my Alberta buddy gave me.Your thread must have triggered that dream.
I just now flashed back on last nights dream.A beauty little milling machine w/ all kinds of tooling and gauges that my Alberta buddy gave me.Your thread must have triggered that dream.
Dennman- Posts : 1446
Join date : 2012-10-31
Age : 75
Location : Courtenay
Re: Made some chips w the SouthBend
Here's the spacer, aluminum. BTW Denn, I'm gonna post a thread about Koot handbombing his bike last nite, over on the Shovelhead forum...check it out in about half hour.
sunnydog- Posts : 2053
Join date : 2012-10-28
Age : 55
Location : Akimbo Alogo
Re: Made some chips w the SouthBend
Just a thought here John.Will you build a dummy spacer for the other side to balance the look?
Dennman- Posts : 1446
Join date : 2012-10-31
Age : 75
Location : Courtenay
Re: Made some chips w the SouthBend
Yes Denn, I got a spacer for that side already, which I used on same axle before. I agree, gotta balance the look.
sunnydog- Posts : 2053
Join date : 2012-10-28
Age : 55
Location : Akimbo Alogo
Similar topics
» Den did you get the pistons
» Horse thief roll call. Rainbow chasers inc
» mother mary,s
» Made it back from the Hunting Trip
» Out of province motorcycle inspection
» Horse thief roll call. Rainbow chasers inc
» mother mary,s
» Made it back from the Hunting Trip
» Out of province motorcycle inspection
48-84 :: Your first category :: 66-84
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum